How to change IP of already installed cameras?

March 11, 2019, 9:58 am

≫ Next: HikVision NVR: DS-7732NI-I4(B): "B" revision ?

≪ Previous: Hikvision's 7604-K1 four camera NVR

$

0

0

Hi, i am changing my NVR (Vortec POE) to a HikVision DS-7608NI-I2-8P and want to keep existing cameras for a while.

Is there a way to change the IP address of the cameras while they are in situ? I understand how to do it “on the bench” with a 12v supply and PC on corresponding IP. But can it be done over POE from the NVR, when their IP addresses are totally different?

---

HikVision NVR: DS-7732NI-I4(B): "B" revision ?

March 11, 2019, 2:05 pm

≫ Next: Grass looks like its covered in Snow

≪ Previous: How to change IP of already installed cameras?

$

0

0

Local seller has "B" revision, which is different to plain "DS-7732NI-I4":

1. HDMI output: 2 ports vs. 1
2. eSATA port (doesn`t exist on DS-7732NI-I4)

Description in English: https://www.sensorsecurity.co.za/app/uploads/2019/02/DS-7732NI-I4B.pdf
Description at Hikvision website(RU): https://hikvision.ru/media/storage/passport/2xxx/ds-7732ni-i4b.pdf (model is not shown for non-EE regions)
Mentioned at FW release notes...

HikVision NVR: DS-7732NI-I4(B): "B" revision ?

Grass looks like its covered in Snow

March 11, 2019, 2:12 pm

≫ Next: Swapping two cameras

≪ Previous: HikVision NVR: DS-7732NI-I4(B): "B" revision ?

$

0

0

Is it normal for grass at night to look like a heavy snow fall
I have a hi 121 hi look dome camera looking down above a bedroom window

Is there anything i can do to reduce the reflectvity of grass at night

I am using Ispy free software

Swapping two cameras

March 11, 2019, 3:53 pm

≫ Next: Finally added 2nd camera outside

≪ Previous: Grass looks like its covered in Snow

$

0

0

I'd like to swap a 6mm cam in my garage ("Garage Cam") for the 4mm cam in my backyard ("Backyard Cam"). I think the coverage will be better at each position after the swap. Couple of questions:

Is this a simple matter of powering down the system, swapping the cameras, and powering the system back up?

Or:

Will I need to do anything else, such as resetting the cameras prior to the swap and start fresh?

I also don't know if each camera's settings follow the camera, or do those settings...

Swapping two cameras

Finally added 2nd camera outside

March 11, 2019, 5:00 pm

≫ Next: User Access denied on streaming image through browser

≪ Previous: Swapping two cameras

$

0

0

Greetings from USA. Though I had camera working POE for a couple months on a desk in the house, there were enough issues (Winter, primarily) to avoid the install. Camera is ~200’ away, through two patchfields. Prior to permanent install I ran it hand held outside garage, verifying that it would work this far away, and testing to make sure Image wouldn’t be shooting the LED Motion detect floodlight on the house. It worked, and Image was fine, so when weather broke did the install.

Nosy for...

Finally added 2nd camera outside

User Access denied on streaming image through browser

March 12, 2019, 1:01 am

≫ Next: Hikvision ANPR upload Video event

≪ Previous: Finally added 2nd camera outside

$

0

0

Hi,

I have a DS-2CD2142FWD-I and have created two users (apart from admin), UserA and UserB.
UserA is type of "User" and has only "Remote: Live View" permission
UserB is type of "Operator" and has all permissions.

I am trying to let them get a picture from the camera through a browser using the following URL:

http://myip/ISAPI/Streaming/channels/101/picture.

The browser prompts for credentials and when I provide the admin account everything works fine. I can see the camera...

User Access denied on streaming image through browser

Hikvision ANPR upload Video event

March 12, 2019, 3:27 am

≫ Next: HiWatch HWI-D640H-Z : How to PTZ ?

≪ Previous: User Access denied on streaming image through browser

$

0

0

Hi
I have an Hikvision DS-2CD4A26FWD-IZS/P - which has ANPR facilities. I have got it configured so when a number plate is identified it will upload a picture of the vehicle to an FTP server - this has been working great. However I would like to get it to also upload a short video 5 secs before and after the picture is taken and upload it via FTP. Is hsi possible, I have had a look at the events in the web console but nothing jumps out at tme on how to do this. Any help would be much...

Hikvision ANPR upload Video event

HiWatch HWI-D640H-Z : How to PTZ ?

March 13, 2019, 5:31 am

≫ Next: Using a UPS with Hikvision NVRs

≪ Previous: Hikvision ANPR upload Video event

$

0

0

Hello friends,
I would like to ask you for your help. We bought Hikvision DS-7732NI-I4/16P NVR and HiWatch HWI-D640H-Z cameras. We already managed to get the cameras working, but we are no table to pan/tilt/rotate them, or at least I am clueless how to do that. In PTZ section of NVR interface, the cameras are not moving in any direction when I try to use PTZ controls.

(PS: This is my very first post here, so I apologize, if I missed any additionall info)

---

Using a UPS with Hikvision NVRs

March 13, 2019, 6:50 am

≫ Next: How to use Optio Cameras with a Synology NAS

≪ Previous: HiWatch HWI-D640H-Z : How to PTZ ?

$

0

0

Hikvision do recommend using an Uninterruptible Power Supply (UPS) with their NVRs if you wish to protect/maintain the power supply.

If you are using POE from the NVR to power your IP cameras, then the UPS will in fact keep your whole IP CCTV system running during a power outage.

However, currently none of the Hikvision range of NVRs offer any connectivity to interact with a UPS and shutdown safely before the UPS power finally runs out...

Using a UPS with Hikvision NVRs

How to use Optio Cameras with a Synology NAS

March 13, 2019, 7:53 am

≫ Next: Hello I am getting Error code HCNetSDK.dll[13] (No permission) when I try and connect to a stream.

≪ Previous: Using a UPS with Hikvision NVRs

$

0

0

Optio is designed to be used as a complete system (Optio cameras with an Optio NVR) and this makes it an excellent option for small home/business systems. At the same time the Optio cameras are ONVIF compliant and so you can connect them to 3rd-party recording devices, and a common 3rd-party option is a Synology NAS which a lot of people already have in their homes & business for general file and media storage. Synology NAS devices have their own security software called Surveillance...

How to use Optio Cameras with a Synology NAS

Hello I am getting Error code HCNetSDK.dll[13] (No permission) when I try and connect to a stream.

March 13, 2019, 8:01 am

≫ Next: NEW Milesight NVR Firmware (7x.9.0.2) Introduces Support for VCA Functions

≪ Previous: How to use Optio Cameras with a Synology NAS

$

0

0

Hello our Hikvision DS-7216HGHI-SH is not allowing a new user to view video streams. We are attempting to view via the iVMS-4200(v2.04.00.04).exe software.
We can go into iVMS 4200 client and the user is registered there as a Super User. On the Actual main head unit, the user is rated as a "user". They can connect to the cameras in device management and list the cameras on the main head unit. However when it comes to viewing the stream we get the attached error.
Can you help fix this error...

Hello I am getting Error code HCNetSDK.dll[13] (No permission) when I try and connect to a stream.

NEW Milesight NVR Firmware (7x.9.0.2) Introduces Support for VCA Functions

March 13, 2019, 12:54 pm

≫ Next: Any help appreciated

≪ Previous: Hello I am getting Error code HCNetSDK.dll[13] (No permission) when I try and connect to a stream.

$

0

0

Milesight have just this week released a new NVR firmware, 7x.9.0.2 introduces support for VCA functions which means that you can now control the VCA/Smart Event settings of your Milesight cameras from the NVR.

You can read a little bit more about this new feature here

IMPORTANT: Before updating to 7x.9.0.2 you will need to make sure your NVR has been updated to the new file...​

NEW Milesight NVR Firmware (7x.9.0.2) Introduces Support for VCA Functions

Any help appreciated

March 13, 2019, 3:11 pm

≫ Next: A real discussion about IP bandwith, codecs and quality.

≪ Previous: NEW Milesight NVR Firmware (7x.9.0.2) Introduces Support for VCA Functions

$

0

0

I've just set up floureon ip camera working great throu my andr3phone except with videos emailed to me telling me to open them in th app but soon as the y appear I get this message
Within six hours of searching, no relevant record was found. Please click on the upper right corner to select another time zone.
Cheers kenny

A real discussion about IP bandwith, codecs and quality.

March 14, 2019, 12:52 am

≫ Next: Hik-Connect app Notifications and Playback

≪ Previous: Any help appreciated

$

0

0

Hi,

we know the new generations from hikvision support all H265+ Codec. We know that we save bandwith and storage space.

My calculation says when i using H265, i use 1024kbps every megapixel.

4MP = 4096kbps (My recorder 7616NI-I2/16P sets by his own from 4096kbps to 6144kbps)
8MP = 8192kbps (My recorder 7616NI-I2/16P sets by his own 10240kbps)

The focus for myself is image and video quality.

Videoquality is: ++++ (Anyone see the difference in quality when setting higher plus?)
Bitrate...

A real discussion about IP bandwith, codecs and quality.

Hik-Connect app Notifications and Playback

March 14, 2019, 10:21 am

≫ Next: Hdd showing as uninitalized

≪ Previous: A real discussion about IP bandwith, codecs and quality.

$

0

0

Hi, can you help with the 2 problems I have:-

1. On my Hit-Connect app I get my Notifications but now image, just a bell Icon... any reason why? I haven't change any settings, it just stopped about a month ago, I'v just updated the app and still the same.

also just checked my email account and dont have anything there too. I logged into my NVR and ran a test, and received that email all fine.

and

2. How can I play back downloaded files? I did have H.264+ on but Iv since changed it to...

Hik-Connect app Notifications and Playback

---

Hdd showing as uninitalized

March 14, 2019, 11:58 am

≫ Next: Hikvision DS-9632NI-I8 standby mode

≪ Previous: Hik-Connect app Notifications and Playback

$

0

0

Hi, I've been having a few issues with a hdd in a hikvision nvr showing as failed but after a reboot it clears and shows fine. Today it now displays as uninitalized. How can I initalize this but still keep the content in the drive as the drive is full with recordings?

Thanks

Chris

Hikvision DS-9632NI-I8 standby mode

March 14, 2019, 12:00 pm

≫ Next: Unable to do 50fps on the DS-2CD4025

≪ Previous: Hdd showing as uninitalized

$

0

0

Hi I've read you can have 2 x DS-9632NI-I8 with 1 active and the other in standby mode. It mentions about syncing the devices recordings then the standby will step in and take over recordings if the live one fails. What i need to know is do both units keep the same recordings on them as they are both in sync? So if I have 40 days recordings on the live this gets replicated to the standby so if the standby steps In to take over recordings then it will have the most recent recordings plus...

Hikvision DS-9632NI-I8 standby mode

Unable to do 50fps on the DS-2CD4025

March 15, 2019, 4:35 am

≫ Next: Unbranded N6000-16EFP/48-A

≪ Previous: Hikvision DS-9632NI-I8 standby mode

$

0

0

Hello to all at the Forum,
I have 2 network cameras DS-2CD4025FWD-(A)(P) connected to a NVR model DS-7604NI-E1/4P/A.
I use the system for animal observation and I have been using 25fps, but I would like to record at 50fps (which the specs say it do).
However, I cannot set the record parameters on the NVR to 50fps: I have tried all combinations of Bitrate type/Video quality/Bitrate mode but I got always a "setting failed" message.
I was able to set the Event mainstream to 50fps (but not the...

Unable to do 50fps on the DS-2CD4025

Unbranded N6000-16EFP/48-A

March 15, 2019, 5:30 am

≫ Next: DS-2AE4215TI-D is this an IP camera?

≪ Previous: Unable to do 50fps on the DS-2CD4025

$

0

0

Hi All

Long story short bought this POE DVR for a job in 2017 from Techage, they now refuse to support it advising that it is not their DVR!. Even though they supplied it with their branded cameras. The DVR powers and works fine, but all of the cams drop out and come back, i have a spare cam and i took the unit away and it does it with any camera i install.
I tried powering a camera up by 12v thinking the PSU may be the problem but the camera drops regardless of how its powered by ethernet...

Unbranded N6000-16EFP/48-A

DS-2AE4215TI-D is this an IP camera?

March 15, 2019, 5:42 am

≫ Next: Camera Choice For Key Front Drive/Porch Location

≪ Previous: Unbranded N6000-16EFP/48-A

$

0

0

Hi

I have been told that this is an IP camera (want to access from web only, no DVR/NVR). The spec doesn't seem to suggest this is the case - can anyone can confirm.

Thanks